| View previous topic :: View next topic |
| Author |
Message |
ekimikem
Joined: 02 Aug 2008
Posts: 45
Location: Coeur d'Alene, ID.
|
 Posted: Tue Aug 05, 2008 6:53 pm Post subject: Type 1 and 3 engine parts, bus trans |
 |
|
Stock engine parts 40 hp to 1600
Some 60's and 70's bug parts.
Last edited by ekimikem on Thu Aug 07, 2008 9:05 am; edited 1 time in total |
|
| Back to top |
|
 |
Long-roofs
Joined: 23 Aug 2007
Posts: 715
Location: valley
|
| Posted: Tue Aug 05, 2008 7:40 pm Post subject: Re: Type 1 and 3 engine parts, bus trans |
|
|
| ekimikem wrote: | Stock engine parts 40 hp to 1600
Good used 3 rib bus transmission
Some 60's and 70's bug parts. |
Any type 3 motors? I know Jim is looking for a '70 FI motor.... |
|
| Back to top |
|
|
ekimikem
Joined: 02 Aug 2008
Posts: 45
Location: Coeur d'Alene, ID.
|
| Posted: Tue Aug 05, 2008 8:24 pm Post subject: |
|
|
| I don't have any fuel injection parts, I do have a dual port long block with most of the sheet metal. Not sure of it's condition though. |
|
| Back to top |
|
|
jengel451
Joined: 11 Jun 2007
Posts: 232
Location: Greenacres, WA (yeah, like the show)
|
| Posted: Tue Aug 05, 2008 8:52 pm Post subject: |
|
|
Actually the FI on this Fasty is in good working order. After 9 years in a barn, just had to flush the system out and replace some cracked hose.
Fired right up.
Bottom end is making a horrible racket though. |
|
| Back to top |
|
|
ekimikem
Joined: 02 Aug 2008
Posts: 45
Location: Coeur d'Alene, ID.
|
| Posted: Wed Aug 06, 2008 5:46 am Post subject: |
|
|
| I'll have a look at it today and get back to you this evening. |
|
| Back to top |
|
|
ekimikem
Joined: 02 Aug 2008
Posts: 45
Location: Coeur d'Alene, ID.
|
| Posted: Wed Aug 06, 2008 6:56 pm Post subject: |
|
|
| Well, I checked it out and it looks like overhaul material so no such luck. |
|
| Back to top |
|
|
jengel451
Joined: 11 Jun 2007
Posts: 232
Location: Greenacres, WA (yeah, like the show)
|
| Posted: Wed Aug 06, 2008 7:16 pm Post subject: |
|
|
| ekimikem wrote: | | Well, I checked it out and it looks like overhaul material so no such luck. |
Thanks for checking. I think I'll be dropping this bitch and doing a quick overhaul of the thing. |
|
| Back to top |
|
|
CustomVW
Joined: 13 Oct 2006
Posts: 323
Location: Hillyard off market st. and gordon
|
| Posted: Thu Aug 07, 2008 7:41 am Post subject: |
|
|
"quick" overhual.
you gonna change rod bearings and punch the rear bearing?
that's bad.... |
|
| Back to top |
|
|
jengel451
Joined: 11 Jun 2007
Posts: 232
Location: Greenacres, WA (yeah, like the show)
|
| Posted: Thu Aug 07, 2008 10:01 am Post subject: |
|
|
| CustomVW wrote: | "quick" overhual.
you gonna change rod bearings and punch the rear bearing?
that's bad.... |
Quick as in the time it's gonna take me to do it. Sheesh. |
|
| Back to top |
|
|
|
